The method used to is by reset the printer Error ink cartridges are not installed properly (error E5) : Step 1 : Push Power switch by continue (Push Power On/Off) Step 2 : inserrt plug(Hold and Press Power) step 3 : Push Reset button 1x, Let Power button, Push Reset twice till 0 Step 4 : Push + display change from 0 to 1 (push button + to change 0 to 1) Step 5 : Push Power switch again , Printer will be print 1 page (push power button–>start button till 1 page.) step 6 : Open cover Step 7 : Unplug power cable Step 8 : Take out ink PG 40 and PG 41 Step 9 : Insert plug again Step 10 : Push power switch Step 11 : Open cover (scan cover) Step 12 : Inksert ink PG 40 , PG 41 again These are the step How to Reset waste ink counter (error E16) : 1. Turn off power button (power button is in ), Press and Hold STOP/RESET then Push ON/OFF button 2. Hold ON/OFF button, press STOP/RESET button 2x 3. Let both of button and printer in to SERVICE MODE 4. Printer will be charging 5. Afte...

Try this to reset the error. 1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.) 2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.) 3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green. 4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) 5) Press the Power button. The LED lights in green, and the selected function is performed. (When the operation completes...

Resetting the Waste Ink Volume Counter 1) Enter SERVICE MODE.....By pressing THEN #. 2) Select TEST MODE. 3) Select [8] PRINTER TEST in TEST MODE. 4) Select 3. [EEPROM CLEAR]. 5) Select 0. [INK COUNT]. Let the printer complete its reset cycle (about 20 seconds). 6) Turn the printer off and on by unplugging the power cord and plugging it back in.

Resetting the Waste Ink Volume Counter 1) Enter SERVICE MODE.....By pressing Menu THEN Copy THEN #. 2) Select TEST MODE. 3) Select [8] PRINTER TEST in TEST MODE. 4) Select 3. [EEPROM CLEAR]. 5) Select 0. [INK COUNT]. 6) Press the [OK] key. (On F30 printers, skip step (6) since there is no [OK] key .) 7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

High quality 22ppm black and white printing. Compact design for day to day office use. Easily Network Connected. Manual Service : Download Driver iR1022/1018 : Download

Below is a procedure that in most cases should resolve a Canon i70 waste tank issue 1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.) 2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.) 3) While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green. 4) When the LED stops blinking and lights in green, press the Resume/Cancel button 4 times (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) After the function (menu) is selected, press the Power button. The LED ligh...

1. Printer ‘on.’ 2. Press: “Additional Functions” button Press “Scan” button Press “Copy” button Press “Scan” button 3. Now it says, “Service Mode / #1 SSSW. 4. Keep hitting “+” [which is the right arrow]; it will go through #1 to #11 (Date/Time), then “Service Report,” and, lastly, “Test Mode.” Then hit “Set.” 5. Now you will have another set of selections. Keep hitting “+” [the right arrow] to go from #1(DRAM) to #8 (Printer Test). Then hit “Set.” 6. When it finishes some sort of function, “Please Wait” will be replaced by “-8-2+” Then hit “+” and it should then say “-8-3+” and you hit “Set.” 7. The screen should now say “EEPROM Clear.” [You may need to press “Set” then, to get to the next step? My notes aren’t clear.] 8. Option 0 should be “select ink count.” Press “Set.” 9. Press the “Stop/Reset” button. 10. Press the “On/Off” button. 11. Wait for the printer to restart. I have had the “waste ink tank near full” message twice in the almost-3-years I’ve been using my printer and it’...

1. Put the cartridge on some paper towels in an area where you can tolerate a spill. 2. Peal off the top label. 3. Fill the syringe with 5 ml. of color ink. 4. Very S-L-O-W-L-Y inject ink into each chamber until the sponge is full. A little ink might come out of the top when full, so cover up the other two holes while filling one. 5. When finished, replace the top label or leave it off (it will make no difference in the printing). 6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions. Or print Test pages.